CISCO OFFICIAL EXAM CENTER: 642-732 Exam Questions has been Updated Today!
Cisco Official Exam Center New Released 642-732 Dumps Questions, Many New Questions added into it! Braindump2go Offer Free Sample Questions and Answers for Download Now! Visit Our Webiste, get the new updated Questions then pass Cisco 642-732 at the first try!
Keywords: 642-732 Exam Dumps,642-732 Practice Tests,642-732 Practice Exams,642-732 Exam Questions,642-732 PDF,642-732 VCE Free,642-732 Book,642-732 E-Book,642-732 Study Guide,642-732 Braindump,642-732 Prep Guide
QUESTION 121
Which choice best describes RF challenges for outdoor mesh site survey and deployment?
A. Reflection
B. Reflection, absorption
C. Diffraction
D. Diffraction, scattering
E. Reflection, absorption, diffraction, scattering
Answer: E
QUESTION 122
Refer to the exhibit. After performing a Layer 1 survey using Cisco Spectrum Expert, which result is indicated by the visual screen?
A. Normal 802.11b activity
B. Normal 802.11g activity
C. Microwave oven interference
D. Video camera interference
E. Bluetooth device interference
Answer: A
QUESTION 123
What document is required to build the Statement of Work?
A. pre-survey questionnaire
B. post-survey questionnaire
C. site survey report
D. installation report
Answer: A
QUESTION 124
What RF phenomenon results from a presence of metallic I-beams, conveyor belts, chain-link fences, and metallic shelves found in a warehousing environment?
A. multipath
B. free path loss
C. absorption
D. scattering
Answer: A
QUESTION 125
Which two are impacts of having 802.11b clients in an 802.11g network? (Choose two.)
A. 802.11b clients will degrade throughput of 802.11g clients
B. 802.11b is more susceptible to multipath than 802.11g
C. 802.11b operates over fewer channels than 802.11g
D. 802.11b uses 20 MHz wide channels, 802.11g uses 40 MHz wide channels
E. 802.11b is more susceptible to attenuation than 802.11g
Answer: AB
QUESTION 126
What type of survey is used to assess and analyze existing wireless infrastructure?
A. passive survey
B. active survey
C. predictive survey
D. application survey
Answer: A
QUESTION 127
When planning a site survey, what Cisco tool can an engineer use to estimate the number of required APs?
A. MSE Location Tracking
B. WCS Planning Mode
C. WLC NetFlow Exporter
D. LWAP Monitor Mode
E. WCS Map Editor
Answer: B
QUESTION 128
The wireless survey report shows APs staggered throughout a facility, with several of them placed right on the exterior walls. Other APs are located right at building corners and major turns in the structure layout. Assuming all survey locations are optimized with a minimum of -67 RSSI at cell edges with 20% overlapping cells, for what purpose can this survey model be used?
A. location based services and BYOD preparation
B. voice and data clients with video on demand
C. streaming video with VoIP and data as an option
D. location services, VoIP, data, and video
Answer: D
QUESTION 129
A customer wants to deploy wireless services inside a 500-seat auditorium. Given the volume of potential users in this condensed area, what is the best option for AP deployment?
A. place 802.11n APs along the outside edge with dual-band directional antennas
B. place 802.11n APs along the outside edge with 2.4GHz directional antennas
C. place 802.11n APs along the outside edge with 5GHz directional antennas
D. place 802.11n APs in the center with 2.4GHz sector antennas
E. place 802.11n APs in the center with 5GHz sector antennas
F. place 802.11n APs in the center with dual-band sector antennas
Answer: B
QUESTION 130
A wireless engineer is gathering equipment to perform a point-to-point bridge survey. What three pieces of equipment should be used? (Choose three.)
A. 3502i with dual band directional antennas
B. 3502e with AIR-ANT2460NP-R
C. 1132 with a 10dBi Yagi
D. 1552e with three AIR-ANT2547-N=
E. 1552e with AIR-ANT2588P3M-N=
F. 1310 with internal antenna
G. 1142 Series with internal antennas
Answer: BEF
QUESTION 131
What three best practices should be performed for a Data-Only Survey? (Choose three.)
A. reduce the power to 50% of the client max power
B. reduce the power to 75% of the client max power
C. disable DTPC
D. enable DTPC
E. 5 – 10 percent overlap
F. 10 – 15 percent overlap
Answer: ACF
QUESTION 132
What are the best practice minimum and recommended signal level values for a Location Services Survey?
A. minimum: -65dBm; recommended: 60 dBm
B. minimum: -70dBm; recommended: -68 dBm
C. minimum: -75dBm; recommended: -72dBm
D. minimum: -80dBm; recommended: -78dBm
Answer: C
Braindump2go 642-732 Latest Updaed Braindumps Including All New Added 642-732 Exam Questions from Exam Center which Guarantees You Can 100% Success 642-732 Exam in Your First Try Exam!
